Robs workbench
Moderators: 52D, Tom F, Rlangham, Atlantic 3279, Blink Bonny, Saint Johnstoun, richard
Re: Robs workbench...in works grey...
Should the "Fish" plate be lower as on the "Fruit" van?. Ambis do a nice etch of the Fish and Fruit plates, if you do not know.
-
- GCR D11 4-4-0 'Improved Director'
- Posts: 435
- Joined: Sat Mar 11, 2006 1:19 pm
- Location: Cork Ireland
Re: Robs workbench...in works grey...
hi Mick...
the two Fish are LMS and I'm going pretty blind with them,basically just following the Parkside instructions..apparently built in 1941 with absolute economy lettering,not even LMS.....I need to get a "Tatlow" for the other 3 companies really ....is there an LMS encyclopedia?...I'd happily joint one for the other 3 as I'm overloaded on LNER rolling stock....probably a common affliction!!
the two Fish are LMS and I'm going pretty blind with them,basically just following the Parkside instructions..apparently built in 1941 with absolute economy lettering,not even LMS.....I need to get a "Tatlow" for the other 3 companies really ....is there an LMS encyclopedia?...I'd happily joint one for the other 3 as I'm overloaded on LNER rolling stock....probably a common affliction!!
-
- LNER V2 2-6-2 'Green Arrow'
- Posts: 1100
- Joined: Mon Sep 19, 2011 12:24 am
Re: Robs workbench...in works grey...
Rob,
Bob Essery and I think David Jenkinson produced a 2 volume set I think of LMS Stock.
Old but worth looking for.
Paul
Bob Essery and I think David Jenkinson produced a 2 volume set I think of LMS Stock.
Old but worth looking for.
Paul
-
- GCR D11 4-4-0 'Improved Director'
- Posts: 435
- Joined: Sat Mar 11, 2006 1:19 pm
- Location: Cork Ireland
Re: Robs workbench...in works grey...
...I'll keep a look out the,thank you...seems a bit daft to be producing reasonably accurate LNER stock and part-guessing the others!
-
- GCR D11 4-4-0 'Improved Director'
- Posts: 435
- Joined: Sat Mar 11, 2006 1:19 pm
- Location: Cork Ireland
Robs workbench...
...A very slight update......
Finished this POWsides kit...always thought that models of the Colemans advertising wagons were overcooked but found a photo in one of my PO books where the red contrasted clearly with the rest of the colours and its a thorough job....even the axles and bolt heads all in red!...I presume Colmans would have very few fully decked out like that....I did not attempt the bolt heads! ...and four Dia 3D kits... nearly ready for lettering.....
Finished this POWsides kit...always thought that models of the Colemans advertising wagons were overcooked but found a photo in one of my PO books where the red contrasted clearly with the rest of the colours and its a thorough job....even the axles and bolt heads all in red!...I presume Colmans would have very few fully decked out like that....I did not attempt the bolt heads! ...and four Dia 3D kits... nearly ready for lettering.....
- Atlantic 3279
- LNER A4 4-6-2 'Streak'
- Posts: 6657
- Joined: Fri Jun 26, 2009 9:51 am
- Location: 2850, 245
Re: Robs workbench...in works grey...
A very colourful wagon!
Most subjects, models and techniques covered in this thread are now listed in various categories on page1
Dec. 2018: Almost all images that disappeared from my own thread following loss of free remote hosting are now restored.
Dec. 2018: Almost all images that disappeared from my own thread following loss of free remote hosting are now restored.
-
- GCR D11 4-4-0 'Improved Director'
- Posts: 435
- Joined: Sat Mar 11, 2006 1:19 pm
- Location: Cork Ireland
Re: Robs workbench...in works grey...
....possibly too much!...as hot as the product it advertises!